From the category archives:

Texture

Plaster Faux Finish with Joint Compound?

by THAT Painter Lady on Sunday, July 27, 2008

I am trying to get a venetian plaster look in my house. I wanted to try to use drywall mud to create the texture with deeper / thicker results and I am not sure now how to paint it. Does one have to use the plaster in a can to achieve this look or can I paint over the drywall finish with a product that leaves the darker colors behind and the lighter tones to the surface? ~Rob Paulin

The above picture is of the Old World Plaster Finish that I did a few years ago. www.surfaceswithpaint.com

This is my favorite and most popular finish as a professional. I believe this is what you are trying to achieve with the lighter tones on the surface and the darker tone in the recessed areas.

I prefer NOT to use drywall mud for this finish because you will need to prime it before painting. You also run the risk of moisture getting into it when you start painting, and glazing.

Behr actually makes a texture paint that comes in 2 gallon buckets in both smooth and sand finishes. This can be applied to the wall with either a roller or a trowel. Here are the steps that you will need to follow in order to achieve this finish.

1. Apply Plaster – apply to the wall with a 6″ putty knife, pat the wet plaster with a trowel, and knock down with your 6″ putty knife. This is what gives the plaster pattern & texture.

2. Sand - this step is optional depending on how smooth you want your plaster. I like to spot sand areas where you can see lines left from the trowel. Be sure to wipe away the dust that is left from sanding, with a rag.

3. Paint – you can use any color (light to medium tone). I use 2 coats of latex paint. There is no need to prime with this plaster. Let it dry overnight.

4. Mix Glaze & Paint – This is the fun part. You will need a dark color. Don’t be afraid to pick a dark color, because you will be mixing it – 1 part paint to 3 parts glaze. You will also be washing it off with water, so the glaze will lighten up a lot.

5. Apply Glaze – Use a chip brush and apply in random strokes in a 2 -3 ft section.

6. Wash Glaze In – Have a bucket of water ready, dip a big kitchen sponge into the water, ring out until damp and then wash the glaze into the wall.

7. Wash Glaze Off – Wash out your sponge, ring out the water, and then gently wash off the surface of the wall. The light base color will show through leaving the darker glaze color in the recessed areas of the plaster finish.

I hope this helps. Please keep us posted on how it goes. ~ Dawn

Venetian Plaster Othello

4 Piece Set Plaster Trowel Set

Best Look Faux Finish Glaze

Woolie  Lambwool Faux Appl Tool

Post to Twitter

{ 3 comments }

How to Glaze My Lightly Textured Walls

by THAT Painter Lady on Wednesday, July 23, 2008

“What is the easiest way to apply a purchased glaze to my lightly textured walls?

The room is the kitchen which has texture on the walls like houses built in the 70s. The walls and ceiling are painted with Laura Ashley gold #3. It has been suggested that I use van dyke brown on the walls to age for Tuscan like appearance. My living room and hallway are painted the same gold.

I also painted bookcases and fireplace with a white and plan to use glaze on fireplace. When I painted the fireplace and hearth I rolled on the white lightly on the surface of the brick leaving the dark grout with little change and the texture of the brick rough.

When I apply the brown glaze to the fireplace I just want to tone down the white a little and brighten the brick. So far the built in bookcases on either side of the fireplace look wonderful. ~ Thanks Sharon”

Hi Sharon, I would suggest doing a color wash on your walls. Van dyke brown sounds like a good color to go over the gold. A dark glaze will tone down the yellow and give your walls that Tuscan finish that you are looking for. This book- Paint Style: The New Approach to Decorative Paint Finishes has a section that explains the color wash finish in more depth.

Here are few simple steps that you will need to follow:

1. Gather Supplies

  • Paint
  • Glaze / glaze extender
  • Large kitchen sponge
  • Bucket
  • Rags (for spatters & spills)
  • Paint Brush

2. Mix your glaze – 1 part paint to 3 parts glaze. Use a good quality glaze that has a longer open time. If you already have glaze that dries faster than 15 minutes, then add a glaze extender. Follow the directions on the bottle to see how much you need to add.

3. Brush on Glaze – Apply the glaze to your walls in a criss cross motion

Dish Sponge4. Wash Walls with Sponge – Wring out your sponge in the bucket of water and wash the glaze into the surface of the wall. Dip the sponge again in the bucket of water and then wash off some of the glaze.

Because you have lightly textured walls already. The brown glaze will settle nicely in the recessed areas. You want to wash off the raised areas the reveal the gold color underneath.
photo credit: the Original Muddog

I hope this helps, Let us know how it goes, That Painter Lady

Click here to read one of our recent articles: Painting Techniques Colorwashing With Same Color

Click Here To See TINTABLE GLAZE

Post to Twitter

{ 0 comments }

how to relax in a presentation aiguille du midi cable car binders for music pages dimond chain blood on mri 207 tierney 2007 roto broil oatmeal cookies made with stevia staphylococcus flesh-eating streptococcus anime abuse ann levine ny auto styling accessories